How to Replace a Saab 9-3 Key
The Saab 9-3 is a car that has a large attraction for drivers. It offers good visibility and an impressive performance engine. It has a high safety rating.
However, it's important to make sure that you have two keys working for your car. If you lose just one key, it could be very expensive to add an additional one.
How to replace the ignition Key on a
saab 9 3 key replacement 9-3
If your car key won't start in the ignition you must replace it. This guide will teach you how to replace the ignition key on a
saab 9-5 key replacement 9-3. You'll have to replace the key, buy a new reprogrammable cell, and purchase a new case for your key-fob.
In contrast to older models, the majority of modern Saab cars use an electronic transponder inside the key-fob, instead of a physical key that can be used to unlock and start the vehicle. The rechargeable batteries contained in the key-fob eventually wear out, and they will not be able to hold charge. This is especially applicable if you are using the same key for the same lock.
The good news is that it can be replaced fairly easily by an experienced locksmith. If you have the proper tools, and a little patience you can do it yourself. The first step is to disassemble the key-fob apart. Insert an open-ended head into the slot that is in the middle of your case. The plastic is thin, and is easily damaged.
Once the case is open and you are able to prepare the new key by combining the lower part of the previous key with the transponder and banana on the new key. This will ensure that the new key is properly connected to your CIM and could make a huge difference when replacing the sole key for your Saab 9-3.
How do you replace the ignition Key on a Saab 900
If you don't have two keys, you'll need to remove the steering wheel and dashboard for access to the ignition. Begin by disconnecting the negative battery cable. After the battery has been disconnected, you can take off all trim pieces and dashboard pieces that surround the steering wheel. Once the dashboard is removed, you can insert an screwdriver into the opening behind the ignition switch.
The ignition cylinder has key locks that can prevent the car from starting if the key isn't there. If your 900's ignition switch isn't functioning, check the key to see whether it's inside the lock or is stuck in the ignition barrel. It is also important to rotate your keys and keep them clean to prevent breaking.
saab 9-3 key not accepted contact service cars differ from other cars due to the fact that they don't have traditional keys made of metal. Instead, the car recognizes electric signals generated by the key fob using the use of a special microchip.
If you lose only one working key fob the dealer will charge you the highest dollar to replace the computer module (known as the CIM). We can reprogram the EEPROM on your current computer to make it accept new keys without the need for replacement. This will save you up to 50% of the cost the dealer charges! We call it the SAAB KEY PROGRAM. Find out more about it here!
How to Replace the Ignition Key in the Saab9-5
The metal part of classic Saab keys is simple to copy and does not pose a serious threat to vehicle theft. The electronic portion of the key-fob comes with an embedded chip that can identify the car when the key is inserted into the ignition switch.
Saab has relied on the technology of this anti-theft system for over a decade. It's not quite as effective as a physical lock for your door however it makes stealing your car much more difficult. This is why every Saab owner should always have a spare key on hand.
The majority of new Saabs come with two keys from the factory, but you can purchase additional keys at a dealer through a special handheld computer referred to as a Tech-2. The cost can be under $400 for the transmitter+transponder (different than the metal key blade/shell that opens the doors and turns the ignition cylinder). The only exception is the NG 9-3 cars, which are equipped with more modern and advanced features that require a separate key-fob to utilize a different process.
The dealer will replace the CIM or TWICE module on those cars if keys are lost, and charge you a premium for this. We can reprogram your computer's EEPROM to accept new keys, without replacing expensive modules.
How to replace the ignition Key on an XC90 Saab
It's possible to replace your
saab 93 key programming key fob if you are experiencing issues turning the lock barrel. The process is rather simple and doesn't need you to visit an agent. Instead, you can do it yourself at home by using a few simple tools.
It is first necessary to prepare the new keys. Before you start, disable the anti-theft feature by placing blocks underneath the rear wheels and activating your handbrake. Put the key into the ignition and turn the key to the "on" position. This will activate the accessories, however, it won't start the engine. Repeat this five times and leave the key in the on position.
You'll then need to purchase a new case for your key fob. They can be found in most auto parts stores and are usually very affordable. Based on the model, you may even purchase them without electronic components.
To open up the case, insert an flathead screwdriver into the slot in the middle. Gently work it. Once you split the case, you will have access to all the internal electronic components. Use a flathead screwdriver to gently pry out the electronics.