Reasons Your Fiat 500 Key Fob Won't Work
A key fob with the
fiat punto replacement key 500 number is a convenient way to unlock the doors and start the car. However, there are many reasons why the fob won't be working. This could be due to a dead coin-battery or water damage, problems with the receiver modules, and interference.
This listing is for a NEW replacement
fiat 500x key fob programming Flip Key Remote - like the Ilco brand that needs to be programmed professionally by a local locksmith (click here to search for a Locksmith Search). It includes lock, unlock, and trunk buttons.
Dead Coin Battery
A dead battery is probably the most common reason for your 500 key fob that isn't working. Key fobs of today have an operating range that is limited and must be within a few inches of your vehicle in order to function. If you're far from your vehicle and press the key fob button, the car won't respond and will display a "Key Fob Not Detected" message in the instrument cluster.
If this happens, replace the battery in the coin cell (Part number CR2032) by a new one from a reputable brand like Panasonic, Duracell, or Energizer. They are usually available at your local hardware store, or online.
You can test the battery of your coin-cell by pressing the buttons while you are standing close to your Fiat 500. The car should blink its parking lights, and the key fob will operate the lock and unlock buttons.
If your key fob doesn't work even after replacing the battery, it might be water damage that hinders it from communicating with the module inside your vehicle. Water damage can happen in many ways, including the simple splash or submerging your key fob in saltwater at the beach. If you think your fob was exposed to water, place it in a rice bag to draw out the moisture. If that doesn't work your fob is likely to need to be reprogrammed by an experienced locksmith or dealer.
Water Damage
While the fob has some rubber seals that keep water out of the electronic chip inside it, submerging it in the ocean or washing it in a machine can cause water damage. Saltwater is particularly dangerous to the fob's circuit board, causing it to short out and eventually die. It's not good to let the fob get wet however, don't give it up even if you accidentally drop the fob in water, or fail to take it out of your pocket.
First, remove the battery. Before replacing the battery clean the electronic chip using isopropyl or another similar product. Test the fob next to check if it's functioning. If the key does not work, it may have to be reprogrammed. This is usually handled by an auto locksmith or dealer.
If the key is more recent and hasn't been programmed to your vehicle It will most likely need to be replaced completely. This is a simple procedure that can be completed by a professional locksmith for automotive use. The locksmith will have to cut the key to match the ignition in your vehicle. They'll also need to reprogram the fob to the system of your car. It's a simple and affordable process that can usually be completed on the same day.
Receiver Module Issues
One of the simplest reasons why your 500 key fob might stop functioning is that it's out of range. The remote has a range of 30 feet. Therefore, when you're too far from your vehicle it won't be able to respond to your commands. It can be solved by moving it closer to your vehicle until it begins responding.
If your fob does not work after you replace the coin battery, also known as a "button", "watch" or "button" or "button", it could be due to an issue with the internal circuit board. In the majority of cases, reprogramming your fob will fix the problem. You can find instructions on how to unlock
fiat 500 new key cost uk 500 boot without key -
visit these guys - to do this for most vehicles by searching YouTube or reading the owner's manual.
It is possible to replace the metal retaining clips that keep the coin battery in place. If they become loose, it can stop your coin battery from sitting properly and cause your remote to malfunction.
In rare instances, the fob may be out of sync with your vehicle because of software or hardware problems. This could cause a significant issue, but you are able to often fix this by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain instances it is possible that the software will require reinstallation into your body control modules.
Interference
In addition to a dead coin battery the key fob could not be receiving or transmitting the signal due to interference. This could happen if the key fob is located near an electronic radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. The key fob might not function because of a weak connection to the buttons, water damage or damage to the internal chips.
If the key fob stopped working one day in the middle of the night or after trying everything you can do at home to resolve it e.g. You may have a faulty 500 receiver module in the event that you've tried replacing the battery, reprogramming, or using a spare key fob. The receiver module is situated under the dash and receives the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.
There's a simple method to reset the 500's in-board system, including the keyfob. Disconnect the battery for 15 minutes by removing first the negative cable, then the positive cable. Then, reconnect the battery. This will remove any remaining electrical charge and restart the car's computers. This could allow you to the key fob to function again. If the issue persists, you should consult an experienced technician. They'll be able to determine the root of your problems.