Reasons Your
fiat key programming 500 Key Fob Won't Work
A
fiat 500 stolen without keys 500 key fob is a convenient method to open the doors and start the car. There are a myriad of reasons the key fob might stop working. This includes a dead battery and water damage, as well as problems with receiver modules, as well as interference.
This listing is for an NEW replacement
fiat panda Key fob replacement Flip Key Remote that looks like the Ilco brand. It needs to be professionally programmed (click here to search for local locksmiths for your vehicle). This remote includes lock, unlock and trunk buttons.
Dead Coin Battery
The most frequent reason that your 500 key fob won't work is an inactive battery. Modern key fobs only have a limited range of operation and must be within just a few inches of the vehicle to function. If you are further away from your vehicle and press the keyfob button it won't respond and display the message "Key Fob Not Detected".
If this happens then replace the battery for your coin-cell (Part Number CR2032) with a new battery from a reputable brand like Panasonic Duracell or Energizer. You can usually find them in your local hardware store or online.
You can test the coin-cell battery by pressing the buttons while standing close to your
fiat 500 replacement key near me 500. The car should flash its parking lights and the key fob should be able to operate the lock and unlock switches.
If your
key for fiat 500 fob still isn't working after replacing the battery, there might be water damage that has prevented it from interacting with the module in your vehicle. Water damage can happen in many ways, such as an easy splash or submerging your key fob in saltwater at the beach. If you believe your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this doesn't work, your fob is likely to need to be reset by an experienced auto locksmith or by the dealer.
Water Damage
Water damage can occur if you immerse the fob in the ocean or wash it in a machine. Saltwater can be particularly harmful to the circuit board of the fob which causes it to short out and eventually die. It's not a good thing to submerge the fob in water but don't give up even if you accidentally drop the fob in the water or don't take it out of your pants pocket.
Take the battery off first. Clean the electronic chip using isopropyl alcohol or a similar product and dry it completely before replacing the battery. Check the fob to see if it is working. If the fob doesn't work it could need to be changed. This is usually handled by an auto locksmith or dealer.
If your key is older and not programmed for your vehicle You will need to replace it completely. A professional locksmith for automotive can complete this simple process. The locksmith will require the key to be cut to match your car's ignition. The locksmith will also have to reprogram your fob in the vehicle's system. This is a cheap and quick process that could be completed in the same day.
Receiver Module Issues
Your 500 key fob might not function because it's out of range. The remote has a maximum range of 30 feet, which means if you are too far from your vehicle it will not respond to your commands. It's easy to solve this problem by moving the remote closer to your vehicle until it responds.
If your fob doesn't work after you replace the battery in the coin, also known as a "button", "watch" or "button", it may be due to a malfunction on the circuit board inside. Reprogramming your fob can resolve the issue. The instructions are available for most vehicles on YouTube or in the owner's guide.
It is possible to replace the metal retaining clips that keep the battery of your coin in place. If they lose tension, they could stop the coin battery from being seated properly and could cause the remote to malfunction.
In rare instances, the fob may be out of sync with your vehicle because of hardware or software issues. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some cases they may have to reinstall the software in your body control module as well.
Interference
In addition to a dead battery on a coin The key fob might not be able to receive or transmit an signal due to interference. This is possible when the key fob is near the radio transmitter (cell phones and radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob could not function could be due to a weak connection to the buttons or damage to the internal chip, or water damage.
If the key fob failed to work one day without notice and you've tried every option at home to fix it e.g. replacing batteries, reprogramming or using the spare key fob, it could have a faulty receiver module on your 500. The receiver module, which is located under the dashboard, receives radio frequency signals from your key fob. It converts them to electronic commands that the vehicle interprets.
There's a simple method to reset the 500's internal system, including the keyfob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then, reconnect the battery. This will clear any residual electricity, and restart the computer of your car. This could help you get your key fob working again. If the issue persists, you should speak with an expert technician. They will be able to identify the root cause of your issues.