Reasons Your
fiat punto key replacement cost 500 Key Fob Won't Work
A key fob for the Fiat 500 is a convenient method to open the doors and start the car. However, there are numerous reasons why the key fob might stop functioning. This could be due to a dead battery and water damage, as well as issues with the receiver module, and interference.
This listing is for a NEW replacement
fiat keys Flip Key Remote that appears similar to the Ilco brand. It has to be professionally programmed (click here to search for local locksmiths for automotive locksmiths). It includes lock, unlock and trunk buttons.
Dead Coin Battery
A dead battery is the most frequent reason for your 500 key fob being inoperative. Modern key fobs have a limited operating range and should be within a few feet of the car to operate. If you're far from your vehicle, and you press the key fob button the car will not respond, and will display an "Key Fob Not Detected" message in the instrument cluster.
If this happens you need to replace the battery of your coin-cell (Part Number CR2032) by a brand new one of a trusted brand such as Panasonic Duracell or Energizer. You can find them in your local hardware store, or online.
You can test the coin-cell battery by pressing the buttons while standing close to your
fiat key fob not working panda key fob replacement (
click this link now) 500. The car will blink its parking lights and the key fob should work the lock and unlock switches.
If your key fob isn't working even after replacing the battery, there could be water damage that is preventing it from interacting with the module inside your vehicle. Water damage can occur through a variety of methods, including an easy splash or submerging your key fob in saltwater at the beach. If you suspect that your fob was exposed to water, put it in a rice bag to draw out the moisture. If this isn't working, you'll need to have the fob changed by an auto locksmith or dealer.
Water Damage
While the fob comes with rubber seals that keep water out of the chip's electronic circuit and out of the ocean or washing it in a machine could cause water damage. Saltwater poses a particular risk to the fob's circuit board that can cause it to short out and eventually die. Getting the fob wet is not a good idea, but if you drop it into a cup of water or forget to take it out of your pants pocket prior to running the washer do not give up hope.
Take the battery off first. Clean the electronic chip using isopropyl or a similar product and dry it completely before replacing the battery. Check the fob to verify if it's functioning. If the fob doesn't work it could need to be reset. This is typically done by a dealer or professional auto locksmith.
If the key is newer and was not programmed to your car, it will likely need to be replaced completely. This is a simple process that can be completed by a professional locksmith for automotive use. The locksmith will need to cut the key to match the ignition of your vehicle. The locksmith will also have to program your fob into the vehicle's system. This is a simple and inexpensive process which can be completed within the same day.
Receiver Module Issues
One of the simplest reasons why your 500 key fob won't be working is because it's out of range. The remote has a maximum range of 30 feet. Therefore, if you are too far from your car it will not respond to your commands. This can be easily fixed by moving closer to your vehicle until it begins responding.
If you've replaced the battery on your coin (commonly called a "button" or "watch") and the fob isn't working, it could have an internal circuit board problem. In the majority of cases, reprogramming your fob will resolve this problem. You can find the procedure for most vehicles on YouTube or in the owner's manual.
It could be necessary to replace the clips made of metal that hold the coin batteries in place. If they loose tension they could stop the battery from being properly seated and could cause your remote to malfunction.
In rare cases, the fob may become desync'd with your vehicle due to software problems or hardware issues. This issue can be fixed by visiting your local auto-locksmith or dealer to reprogram your key fob. In certain situations, they may need to install the software again in your body control module, as well.
Interference
In addition to a dead battery on a coin the key fob could not be able to transmit or receive signals due to interference. This could happen when the keyfob's location is in close proximity to a radio transmitter, like a cellphone or radar detector. Other reasons the key fob might not work could be due to a weak connection to the buttons and internal chip or water damage.
If your key fob suddenly stopped working, or you have tried everything at home to resolve it (e.g. It could be a defective 500 receiver module If you've tried replacing it with a battery, reprogramming or using an alternative key fob. The receiver module, located beneath the dashboard, is able to pick up radio frequency signals from your key fob. It converts the signals into electronic commands, which are then processed by the vehicle.
Fortunately, there's an easy method to reset every single system on board in your 500, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then reconnect the battery. This will get rid of any remaining electricity and restart the car's computer system, which can help you the key fob to function again. If the problem persists you should seek the advice of an expert technician. They'll be able to diagnose the exact cause of your issues.