Repairs to uPVC Windows
uPVC windows are a fantastic choice for modern homes. They are long-lasting, durable and easy to maintain. They don't decay or
upvc window repair rust as timber and aluminum.
It is essential to clean and oil
Upvc Window repair windows and
upvc window repair doors regularly. This will prevent unnecessary repair costs as well as increase energy efficiency.
1. Broken Glass
If the glass in your window is broken it can cause a huge deal of damage to your home, making it extremely dangerous and possibly fatal. It is essential to ensure that your windows are in good working order.
Single-pane windows are fairly simple to replace, and they will usually fit into the frames that were previously in use very easily. If you have double-paned windows that are held together by internal beading, it is harder to remove and replace the old panes. In this situation it is essential to purchase plastic spacers to make sure that the new pane fits into the window frame.
If you plan to attempt to remove the window panes yourself, it is essential to wear the appropriate safety equipment that includes gloves with a thick layer of material and protective eyewear. You should also lay down a drop cloth before you begin working on the window panes so that any shards fall on the fabric, not onto the floor and could be trampled.
It's a great idea cover the gap with tape after the glass has been removed. This will prevent water and drafts from entering your home until a professional comes out to repair the window. It also acts as a barrier that will prevent any intruders to gain access into your home. If the gap between the window and the door is large, you might prefer security screens that includes an opening. This will give you the best of both.
2. Sagging
uPVC windows and doors are a cost-effective energy-efficient, durable and long-lasting alternative to timber sash windows. However, over time they can suffer from a variety of issues, including sagging. A window that is sagging can cause problems with light, draughts and even security. It's crucial to act immediately if you discover that your uPVC windows are sagging.
To fix a window that is sagging you can try to reposition the hinges. First, you'll need to unblock the windows so you can reach the frame. Then, using an screwdriver, unscrew the top and bottom hinges and adjust them by turning them clockwise or anti-clockwise. After you've repositioned the hinges, close your window and verify the an appropriate fit. If you're satisfied with the fit of your window, tighten the screws to secure them in the right position.
If you aren't able to move the hinges you may require replacing the seal. As time passes, rubber seals lose their elasticity and dry out and cause them to lose tightness. It is essential to replace your seal as quickly as you can to ensure that your uPVC window waterproof and draughtproof.
UPVC handles can also become loose. Often it is due to screws that have become loose over time. However, it could be due to the fact that the handle mechanism has worn out. It's a good thing that it's simple to fix the loose uPVC window handle yourself. First, you'll need close the window and then perform an initial test to ensure that it fits. The joint at the corners of the sash should align with the joint on the casing. If it doesn't, you can use a screwdriver or a wrench to loosen the handle and reverse the mechanism back into the position it was in.
3. Water Leaks
It is essential to act if you awake each day to find a smoky wall and wet floors. Leaks of water from windows can cause structural damage to your home and impact your ability to regulate the temperature in your home. Most of the time, uPVC window leaks are caused by damaged or missing sealant.
This is a fairly simple fix that can be completed by any competent DIYer. Depending on the severity of the issue is, the old caulking may have to be removed. It is important to remember that when it comes to uPVC window repairs, you should not be tempted to 'over-caulk' as this will only make the area harder to clean and reduce your energy efficiency.
Check that any drainage holes do not have debris in them and ensure that the sill pan has been properly angled to allow the water to drain from the window. In more serious cases you may need to think about replacing the window.
Moldy sills and rotten ones are another sign of water leakage. The fungus thrives in humid conditions and can propagate quickly throughout the house.
It is also important to remember that if the leak originates from the glass in your
double glazed window repairs near me glazed windows, it is more likely to be a problem with the glass seal rather than the frame or sliding. A uPVC specialist can easily fix this issue by replacing the glass seal. This will restore the full insulation of your windows.
4. Faulty Hinges
If your uPVC windows are stiff to open, or loose and open with a breeze it could be the hinges that are at the fault. Anyone with the skills to fix them can replace hinges in just a few minutes.
Nearly every home in the UK will have either top hung or side-hung uPVC windows that use hinges and like any mechanical part they can wear down over time. It's very simple to replace a hinge on a window but it's much easier if someone helps you to hold the frame.
Check that the uPVC hinges are closed and open in the correct direction. You can check this by looking for the arrows on each hinge. This shows which way the window should be opened.
The problem with the hinges on windows could be the result of incorrectly opening the
window repair near me a certain manner or because of poor installation at the factory. Sending us a picture via our website is often enough to solve the issue. We are happy to provide assistance.
Regularly lubricating hinges is also essential. Applying a light engineering lubricant on the hinges is a good way to do this. We recommend using a lubricant that does not contain solvents, like 3-in-1 Multi-Purpose oil. Regular lubrication can allow the window to open and close more easily. It can also lower the possibility of a window sticking and prevent corrosion. Ideally, you should do this once a year. WD40 and other solvent-based lubricants should not be used since they could damage your uPVC windows.
5. Draughts
Draughts can be caused by a variety of different things. The hinges may also become disaligned as a result of wear, causing an opening where the sash meets frame. If they are beyond repair, it might be necessary to have them realigned. In addition, the interlock could also become unbalanced. It is located on the hinge side and could require to be cleaned. In some instances it might be necessary to replace them.
These seals can wear down or get damaged over time, allowing air escape. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity glass. This will help to regulate indoor temperatures, and reduce the risk of draughts.
One of the most effective ways to reduce the draughts in your home is to use a draught excluder, these are typically fabric tubes which are filled with a type of filler. They can be placed on the top of your windowsill. They can help stop cold air from entering and keep your home warm and cozy!
Your windows made of upvc will remain a great source of insulation and security for your home with regular maintenance and repairs. It is important to remember that all windows will eventually wear out and it is cheaper to replace them rather than repair them. If you have any problems with your window made of upvc you should consult a professional as soon as you can.