Upvc Window Handle Replacement (
Http://Www.Huenhue.Net/Bbs/Board.Php?Bo_Table=Review&Wr_Id=8401)
Replacing a broken window handle is a easy task and with the right tools it can be done quickly. However, it is essential to know your handle's type and spindle's length prior to purchasing a replacement.
Older uPVC windows have cockspur window handles which have spurs that protrude to the lock of a wedge cockspur striker plate. They can be left- or right-handed and should be matched when replacing.
What type of lock and handle do I have?
There are a variety of upvc window locks and handles each with its distinct advantages and functions. The type of handle that you choose will determine if the locking mechanism you have is effective and if it's easy to open the windows. With time and regular use the upvc handles that are on your windows can be damaged and worn out. This makes them less secure and effective. In some cases they may even fall completely off. If you notice that your upvc window handles have been removed, it's essential to fix them as soon as you can. This will help prevent burglaries, and keep your house secure.
It's a simple job that virtually anyone can perform. You'll need a few tools, but with appropriate knowledge, it's a straightforward process that should only take a couple of minutes. You will need to know the kind of lock or handle you have on your window. This will allow you to choose the appropriate replacement.
Inline Espagnolette Handles
These are the most commonly used kind of upvc handle and are typically located on the outside of your window. They are flat and come with an open latch that is connected to the locking mechanism of the window frame. Inline upvc handles have a spindle that runs through the center of the handle and then into the frame of the window to operate the latch.
Cockspur Handles
These handles are typically located on older uPVC windows and have a distinctive hook-shaped design. Cockspur handles have a single screw that is used to secure the handle to the frame of the window and aren't as secure as other types of window handles.
Handles that turn and tilt
As opposed to the other handles made of upvc the tilt and turn handles can both be rotated to open the window, and turned inwards to allow to allow ventilation. Generally, they have a 7mm spindle at the side of the handle. They are available in left and right-handed versions.
It is important to measure the size of the spindle when purchasing a replacement upvc handle. There are a few that are exactly the same size. Drop something into the middle of the hole to check the length. This is the longest spindle length that will fit your window.
What is the spindle?
uPVC window handles work similarly as doors, with the user turning the handle to open an internal latch within the frame. The latch opens the window, to allow it to be closed and opened. However, sometimes the handles may become damaged, especially if they are regularly used or
UPVC Window Handle Replacement exposed to harsh weather conditions. You may need to replace the handles on your uPVC window if they are not functioning properly.
There are many different types of uPVC handles, including Espag, Cockspur, and Spaded handles. They are designed in a variety ways to fit into uPVC frames. Each handle type uses an individual spindle to lock the window mechanism. This is why it is crucial to know what kind of handle you have installed on your uPVC window so you can find the right replacement.
The base of the handle will inform you what kind of uPVC it is. There should be a'snap in cover over one screw which holds the handle base in the correct position. Once you remove this and you'll be able to observe the second screw that holds the handle base in position. After both screws are removed and you are able to pull the handle from the uPVC.
Once you have removed your uPVC window handle, you will need to carefully remove the old spindle from the locking mechanism. Note the length of the spindle. You will need to purchase a new one that is the same length as the handle that was originally used and the locking device.
The spindle wears out and is unable to operate the locking mechanism. This can be caused by corrosion, damage from continuous use, or even a loosening locking mechanism. If this happens, you'll need to replace both the window handle and locking mechanism to restore the full functionality of your uPVC Windows.
How do I get rid of the handle that was previously attached?
Window handles can be damaged or destroyed over time. It is crucial to fix them as quickly a possible to ensure your safety. It is good to know that replacing a worn or damaged handle is a relatively easy task that can be accomplished in just over an hour and doesn't require any special tools.
To remove the old handle, you first need to remove the screw that is located at the bottom of the handle. Once the screw is removed, the handle can be removed. Another screw will be situated at the base of the handle. This too can be removed. After these two screws are removed, the handle can be detached from the window's base.
After removing the handle, align the fixing holes of the new handle to the holes that are already in the window frame. If there is a cap or sticker on the new handle, remove it if necessary and then screw the handle into the appropriate position. It is essential to ensure that the handle is working after it is put in place. Turn the handle around and make sure the lock mechanism is in place.
Espag handles come with an extra spindle that is protruding from the handle and slots into a multipoint locking mechanism within the frame of the window. Cadenza windows come with a blade with cutouts that are incorporated into the lock mechanism. Cockspur handles are long and hang over the frame of the window or the transom bar crossmember.
Once you have installed the new handle, insert the spindle into the window lock and tighten it. Replace the snap-in cover and screw cap (if applicable) once the handle is securely fixed. Now that the handle is ready to use,
UPVC Window Handle Replacement you can open and close the window a few times to make sure it is working properly and securely.
How do I install the new handle?
It's not difficult to alter the handle on your uPVC windows. The procedure is easy. All you need is a screwdriver, and a bit of perseverance. First, ensure that the handle is not locked. Remove any screws that are visible. You can also replace them with screw caps. After removing the handle it is necessary to take an outline of the length of the spindle that protrudes from the back of the handle. This is vital as it will determine what kind of handle to buy.
Espagnolette handles are the most commonly used type of handle for uPVC windows. They feature a spindle that runs through the handle, and is responsible for a locking mechanism inside the frame of the window. Once the handle is turned it opens the latch on the window, allowing it to open. When used regularly and over time, handles for espagnolette may be damaged.
Cadenza handles are a kind of uPVC handle that is commonly used in tilt and turn
windows replacement. They have a protruding knife that is operated by a multi-point locking mechanism within the window. They are generally more secure than espagnolette handles since they are only accessible from the inside. They can be replaced using the same method as espagnolette handles but you must ensure that the new handle has an angled blade as opposed to a flat one.
Once you have selected the correct handle, you can align the new handle with the existing screw holes prior to screwing it into place. Then, put the screw covers back on and make sure the new handle functions properly. This is accomplished by moving the handle from locked position to the unlocked and then back to the locked position a few times.